> For the complete documentation index, see [llms.txt](https://learn.withessential.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://learn.withessential.com/field-operations/inspection-reports/before-and-after-photos.md).

# Before and after photos on an inspection report

A photo question on an inspection report can be paired with an earlier photo question as its **Before photo**. When a technician takes the After photo in the mobile app, the camera shows the Before photo faintly over the live view, so they can line up the new shot with the old one: same angle, same distance, same framing. The result is a matched before/after pair on the report.

> **Where to find it:** Ask Essential through the Essential Assistant's **Essential Support** tab. Essential staff: Settings → Assets & Reports → choose the asset group type → **Customize** beside the report under **Inspection reports** → **Inspection Form** tab → the After photo question → **Before photo**.

## Before you start

* Report configuration is available to Essential staff with the **Set up Assets & Reports** permission; **Assets & Reports** isn't shown to ordinary business users. To pair two photo questions on your report, open the Essential Assistant, choose the **Essential Support** tab, and tell Essential which question is the Before photo and which is the After photo.
* The report needs two photo questions: the Before question and the After question.
* Both questions must be in the same place on the form: both in the report's main questions (they can be in different steps), or both inside the **same** asset list. When both are in an asset list, every asset gets its own pair, and each asset's After photo lines up with that asset's Before photo.
* The Before question must be a single **Photo** question. The After question can be a **Photo** or **Photos** question; with **Photos**, every new photo the technician takes is lined up with the same Before photo.
* Questions inside a repeatable list section can't be paired.

## Pair the questions

Essential sets up the pairing for you when you ask through the **Essential Support** tab. These are the steps Essential staff follow in the report editor. If the report doesn't have both photo questions yet, ask the chat assistant in the editor (bottom-right) to add them first.

1. Go to **Settings → Assets & Reports** and choose the asset group type.
2. Choose **Customize** beside the report under **Inspection reports**, then open the **Inspection Form** tab.
3. Find the After photo question. Under it, open **Before photo** and choose the Before question. **Before photo** only appears on a photo question when another Photo question is in the same place on the form.
4. Choose **Save draft**, then **Publish** when the report configuration is ready. Reports started after publishing use the pairing.

To remove the pairing, choose **None** in **Before photo**. The two questions stay on the report; only the overlay is removed.

Removing the Before question clears the pairing automatically. Only a pairing edited to point at a missing or unreachable question shows an error naming the After question; the editor won't save or publish until you choose another Before photo or **None**.

## What the technician sees

On the mobile app, the After question shows **Lines up with** and the name of the Before question under its label.

When the Before question already has a photo, tapping **Take Photo** on the After question opens the before/after camera:

* The Before photo appears faintly over the live camera view. Tap the **Ghost** control under the shutter to switch between **Ghost 50%**, **Ghost 25%**, and **Ghost off**.
* Press and hold the small Before thumbnail to see the Before photo at full strength; let go to return to the camera. Tap the thumbnail to keep it at full strength, and tap again (or change the **Ghost** setting) to go back.
* After taking the photo, tap **Use photo** to keep it or **Retake** to try again.
* Tap **Use standard camera** at any time to take the photo with the phone's normal camera, without the overlay.

The photo is saved, uploaded, and available for markup exactly like any other report photo. Choosing photos from the library with **Select Photo** or **Select Media** works as usual.

Other situations:

* **The Before question has no photo yet.** **Take Photo** opens the normal camera.
* **The Before photo can't be shown**, for example because it was taken on another device and the phone is offline. The before/after camera opens with the note **Before photo isn't available right now** and no overlay. The camera still works, and **Use standard camera** is available.
* **On the web app** there is no camera, so office users upload photos to the After question as usual.
* **Older versions of the mobile app** open the normal camera. Update the app to get the before/after camera.

## On the report PDF

The PDF prints both photo questions wherever the report template places them, the same as any other photo question. To show the two photos side by side, ask Essential to adjust the report template through the Essential Assistant's **Essential Support** tab.

## Related guides

* [The field types you fill in on a report](https://learn.withessential.com/field-operations/inspection-reports/the-field-types-you-fill-in-on-a-report.md)
* [Fill inspection reports on mobile](https://learn.withessential.com/field-operations/mobile/fill-inspection-reports.md)
* [Link a report photo question to an asset photo attribute](https://learn.withessential.com/field-operations/inspection-reports/link-a-report-photo-question-to-an-asset-photo-attribute.md)


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://learn.withessential.com/field-operations/inspection-reports/before-and-after-photos.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
